language

Home

Equipment Usage

The machine is widely used in drying raw materials of mechanism sand, yellow sand, all kinds of tailing sand, slag of cement plant, clay, coal, mixture, iron powder, building materials, chemical industry, foundry and other industries.

Main application

Three-cylinder dryer is mainly used to dry certain humidity and particle size of domestic granular materials, such as dry mortar industry used in the mechanism of sand, river sand, sand, sand, foundry industry with a variety of specifications of sand, building materials and cement industry with the blast furnace water-quenched slag, steel slag, fly ash and so on.

Equipment Characteristics

1. The equipment covers a small area.

2. Moisture in the material is ensured to be below 0.5%, which is the preferred product for dry mortar and slag powder production line.

3. The thermal efficiency of cylinder self-insulation is up to more than 80%, which improves the thermal efficiency by 45%.

4. Fuel can be adapted to coal, oil, gas biofuel and so on. Can dry the block, granule, powder material below 20CM.

5. Than a single cylinder dryer to reduce the footprint by 50%, civil investment by 50%, power consumption by 60%.

6. Made of alloy steel plate, 4 times more wear-resistant than ordinary steel.

7. According to user requirements can be easily adjusted according to the required final moisture index.

8. Low temperature of out gas, long time of using dust removal equipment.

9. No need for large and small gears to rotate, adopting pallet rotation.

10. Discharge temperature is lower than 60 degrees Celsius, continuous production and packaging.

Technical Parameters

Project unit		φ2.0x6m	φ2.5×6.5m	φ2.7×7m	φ3x7m	φ3.2x7m	φ3.6×8m	φ4.2×8.5m
Outer cylinder diameter (m)		2.0	2.5	2.7	3	3.2	3.6	4.2
Outer cylinder length(m)		6	6.5	7	7	7	8	8.5
Cylinder volume(m³)		18.84	31.89	40.5	49.46	56.26	81.38	118
Cylinder speed(rpm)		3-10	3-10	3-10	3-10	3-10	3-10	3-10
Residence time of material(min)		12-30	12-30	12-30	12-30	12-30	12-30	12-30
Initial moisture of material (%)		6-25	6-25	6-25	6-25	6-25	6-25	6-25
Final moisture of material (%)		≤1	≤1	≤1	≤1	≤1	≤1	≤1
Maximum inlet air temperature (℃)		750-900℃	750-900℃	750-900℃	750-900℃	750-900℃	750-900℃	750-90o℃
Production capacity (T/H)	Slag	15-20	20-25	25-30	30-35	35-40	45-60	65-80
	Coal ash	5-12	12-16	15-20	18-22	20-25	25-40	40-58
	Quicksand	15-22	20-35	22-40	25-40	30-45	50-70	70-90
Motor model		Yr160m-4	Yr132m-4E	Yr160m-4	Yr160m-4	Yr132m-5E	Yr160m-4E	Yr160m-4E
Motor power(kw)		7.5×2	11×2	7.5×4	7.5×4	11×4	15×4	18.5×4
Reducer model		XWD-6	XWD-6	XWD-6	XWD-6	XWD-6	XWD-8	XWD-8
Reducer speed ratio (I)		17-29	17-29	17-29	17-29	17-29	17-29	17-29
Equipment weight (T)		22	27	30	33	38	52	72

TAG:

Drying Machine

Three Cylinder Drying Machine

sisoulzg@126.com

+86 13963913992

Classification

Drying Machine

Product Consulting Related Products File Download

Customer visits

Packaging and Shipping

FAQs

My site is not in an ordinary location. Could you provide a corresponding plan to build a dry mortar production line for me?

Of course, we can provide one-on-one customized services to help you not only realize the site construction but also achieve cost reduction and efficiency improvement.

What sand-making equipment is used in the dry mortar production line?

In the realm of dry mortar production, Zhongqinglin Heavy Industry's VK Sand Making Machine has emerged as a core equipment that commands industry attention, thanks to its distinctive design and exceptional performance.

What kind of sand making machine are you using? Is the crushing effect good?

We use vertical shaft impact crushing equipment, and its crushing effect ensures high-quality particle shape. By allowing materials to break along their natural textures, the produced aggregates are cubic, with low content of needle-like and flake-like particles and uniform gradation, laying a solid foundation for high-quality mortar.

What should I do if the aggregate conveyed by the belt is uneven?

It is necessary to adjust the unloading sequence of aggregates to ensure that sand is unloaded last. This is like planning a reasonable driving route for a road, allowing various aggregates to "travel" on the belt in an orderly manner. Secondly, adjust the unloading time interval of various aggregates according to the distribution of aggregates on the belt to ensure that the materials on the belt are continuously and evenly distributed.

What problems will occur with dry-mix mortar admixtures in high-temperature weather?

Water-retaining components such as cellulose ether and starch ether will absorb moisture in the air and agglomerate when the humidity exceeds 80%. This directly causes the water retention of the mortar to decrease by more than 30%, making it prone to bleeding and delamination during construction, and increasing the risk of surface cracking after hardening by 40%.

What problems will occur with dry-mix mortar raw materials in high-temperature weather?

Cement, lime and other cementitious materials have extremely strong hygroscopicity. In high-humidity environments, their surfaces will quickly absorb moisture to form calcium hydroxide lumps. When caking is severe, lumps with a diameter of over 5mm may block the discharge port of the screw conveyor, causing the measurement deviation of the batching scale to exceed ±2%, and may even cause jamming and damage to the blades of the mixing equipment. If the storage silos for admixtures such as fly ash and slag powder are not tightly sealed, in an environment with a relative humidity >75%, fine particles will agglomerate into spherical particles with a diameter of 1-3 cm due to surface tension. These "pseudo particles" tend to form an "arch bridge" structure at the cone of the silo during the falling process, resulting in material flow interruption. If the initial moisture content of aggregates such as fine sand and quartz sand exceeds 3%, the moisture is difficult to naturally evaporate in a hot and humid environment. When these high-moisture aggregates are mixed with cement, a "pre-hydration" phenomenon may occur: the fluidity of the mortar decreases by 20%-30% when it leaves the mixer, the setting time is shortened by 1-2 hours, and in severe cases, "false setting" occurs, resulting in honeycombing and pitting on the construction surface.

Can engineers be sent to our site for installation and training?

We’ll send experienced engineers to the customer's site to guide equipment installation and debug the equipment. We will also provide installation instructions, layout drawings, assembly drawings, etc.

What is the positioning and cost performance of your products?

We have professional engineers, skilled production workers, high-standard quality inspection, and pre-sales and after-sales service teams with effective communication. We can assemble and test all the equipment and pack them carefully before delivery. Maybe our price is not the lowest, but we pursue the best service and quality and we are definitely your most suitable and trustworthy partner.

Are you a factory, a design company, or a trading company?

We are a manufacture factory with our own mechanical and project design engineers. We can provide customized solution design according to customers’ requirement, and full-process services such as early project discussion, scheme design, equipment selection, site planning, equipment layout, transportation and delivery, installation and commissioning.

Can you provide technical and process guidance?

Yes. We have rich experience in mortar production, and we will customize the equipment according to your needs and provide a full range of project guidance. We can reasonably design the layout and site planning according to the size of your workshop, and provide technical support for mortar formulas.

I don't have the formula, can you send me one?

Yes, we have more than 500 customers and they are willing to share the formula.

Get A Quote

Note: Please leave your contact information and our professionals will contact you as soon as possible!

Submit

Related Products

Electronic Control System For Dry Mortar Plant

Fully Automatic Intelligent Control System

Sand Vibrating Screen

Vibrating Screen with Layers

< 1 2 3 4...8 >

Contact

sisoulzg@126.com

+ 86 13963913992

Tel: +86 13963913992

Yuhuangling Industrial Park, Chengyang District, Qingdao, China

Request Quote

Note: Please be sure to fill in the information accurately and keep communication open, we will get in touch with you as soon as possible

Business License

Cookie

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

Cookie

Required

These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.

Analyze

These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.

Feature

These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.

Advertise

These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.